feed power

The paper introduces the main functional design of a kind of small cutting coal machine with hydraulic fork lift as feed power and chain-saw cutting knives driven by generator as working head.

阐述了设计性、综合性实验的含义、定界及内涵，提出了增加设计性、综合性实验比例的途径，分析了设计性、综合性实验在创新型人才培养中的作用。

Two groups of matching relation of the weld speed and the wire feed rate were found in a condition of invariable laser power and focus position.

前者试验获得了一定激光功率和离焦量条件下两组焊接速度和送丝速度的匹配关系，并发现填充焊丝的加入对焊缝咬边现象确有改善；

Multiple modules model of 35 kV feed power system normal running fit for digital simulation

35kV馈电系统正常运行数字仿真的多模块模型

A laser overlaying experiment was studied on 45 steel matrix with special alloy wire by using different laser power, scanning velocity and wire feed rate.

在45钢基体上，选用不同的激光功率、扫描速度、送丝速度，用专用焊丝进行堆焊试验。

The maximum power of liquid-feed direct methanol/ oxygen three-cell stack, where available MEA area was 9 mm2, was 0.285W, and its output voltage and current was 0.7V and 0.407A respectively.

膜电极有效面积为9cm2的的液相进样直接甲醇/氧气燃料电池三电池电堆的最大功率为0.285W，此时输出电压为0.7V，输出电流为0.407A；

The paper discuss its basic working principle, system composition, application requirements for marine use and to which essential and life saving concerning users it shall feed power in case of blackout of ship's mains.

本文阐述了UPS的基本原理，系统构成，船上应用应达到的要求，以及当船上主电源发生故障时应对那些重要和维系生命安全的设备馈电。

The effects of process parameters such as laser power, welding speed, wire feed rate, defocusing distance, laser-wire distance, filler wire angle, shielding gas are studied in detail.

研究了工艺参数对焊缝成形质量的影响，如激光功率、焊接速度、送丝速度、离焦量、光丝间距、送丝角度、送丝方式以及保护气体等，并获得了优化的工艺参数。

A government drive to solve the problem by putting more "distributed" solar cells on the roofs of houses and factories has stalled because of the lack of a smart grid system that allows people and businesses to feed power into the grid and get paid easily.

由于缺乏能让个人和企业较容易地向电网馈电并获得酬劳的智能电网，政府通过在房屋和工厂顶部安装更多“分布式”太阳能电池的解决方案也遇到了阻碍。

Digital Real-time Simulation Model of 35 kV Double-circuit Feed Power System in Normal-operating State

35kV双回馈电系统正常运行数字实时仿真

Analysis and Improvement of 380V Coal Feed Board Power Supply Loop Closing

380V给粉专用盘电源合环原因分析及改进方法

The boiler MFT ( master fuel trip) protection was actuated during start up of feed water pump A of Unit 1 and 2 in Huaneng Shantou Power Plant.

华能汕头发电厂1号、2号机组发生启动给水泵时锅炉主燃料跳闸（MFT）的事故。

Although self-driving power head for combined machine tool has been obsolete, such typical speed-regulating loop as feed power supply still has a bright future due to its high speed-stiffness and efficiency.

虽然组合机用自驱式动力头已被淘汰，但作为其进给动力源的该调速回路，由于其速度刚性和效率均高，仍将有广泛的用途。